#Diy collinear wifi antenna software

This is a great example of how a little bit of math and human ingenuity can be better than expensive test equipment and if you looking to get into software defined radios from scratch, start with Scratch.

So the wavelength of the ADS-B signal is (226,640,000 m/s) / (1090,000,000 Hz) = 0.208m, and the desired length to cut is 104mm 1/2 wave elements and 52mm 1/4 wave elements and get soldering! From there it is simple math – 40m/cycle * 5,666,000 cycles per second = 226,640,000 meters per second or 75.6% of the speed of light. The dip at 5.666 MHz, caused by the reflected signal down the coax is very clearly seen. Using the Digilent Analog Discovery 2’s Network Analyzer the connector is swept from 1kHz to 10Mhz without the cable attached, and then with the cable attached.

#Diy collinear wifi antenna series

The diagram shows the 330 ohms and 100 ohms in series with the center point at around 75 ohm which is a match for the cable.

In order to get the test signal into the cable, just two resistors at the back of a connector are all that was needed. starts his experiment with a 10m cable as he needs a test signal with a wavelength of 40m. When the cable is 1/4th of the wavelength long, the reflected signal arrives back at the start of the signal 180 degrees out of phase – in a perfect world it would completely null out the input signal. A length of coax acts as a stub – any energy that is sent into the cable reaches the far end of the transmission line and is then reflected back to the source. To determine the speed of the signal in the cable, his approach omits the more expensive equipment. As this was a generic cable he had no idea of the dielectric that separates the core from the shield, so the ‘velocity factor’ could be anything depending on the exact composition.

#Diy collinear wifi antenna free

The idea is to use a cable of half the size of the wavelength which is calculated asįor the best reception, the sections of coax need to be half a wavelength long – but the wavelength of the signal inside the coax, which is shorter than the wavelength in free space. We reached out to, and this is what he had to say. There are a number of calculations involved in determining the size of the cable, however, the hack in this design is the way he uses a USB based oscilloscope to measure the speed of RF waves inside the line in question. His design is based on Coaxial Collinear Antenna for ADS-B Receiver by which uses pieces of the coaxial cable cut to the right length. Since the stock antenna was not cutting it, he decided to make one specifically for the 1090 MHz signal. lives near an airport, and decided he wanted to peek into the tracking signals for fun. The ADS-B is transmitted by the aircraft and contains information such as GPS position, pressure, altitude, and callsign among other things at a 1090 MHz frequency, which can be decoded using any of a number of software tools. You will not want a directional antenna on an aerobatic plane, just use it for your ground station.ĭon't let anything conductive near the active part of the antenna, and get it up in the air.Air Traffic Controllers use Automatic Dependent Surveillance-Broadcast (ADS-B) as an alternative to secondary radar to track aircraft. RG 58 cable is lossy so don't run long feeds - use RG 8 to extend the cable with a connector as above. The tricky part was to do this without cutting the shield.Ĭoax segment overall length is 4.6' per segment, overlap to get 4.28' sectionsĭon't use a CB style PL-259 connectors, they are very lossy above 300 MHz, use N, SMA or BNC Then the ends were trimmed to have a short length of center conductor and a short length of shield exposed.

Thus it would be beneficial to use the antenna on the vehicle as well.įirst order of business was to cut the cable into 1/2 wavelength pieces. I'm not worried about directly overhead, because there should be enough leakage to cover any reasonable altitude.Īnother benefit of a good antenna is that by reducing SWR, transmitter heating can be minimized. This would eliminate the need for antenna switching since it is omnidirectional. Since each 3 dB doubles the effective power of the transmitter, this will give about 8 times the power. The antenna is built from 50 Ohm RG 58 coax cable with a theoretical gain of 9 dB over 360 deg.

Decided to build a collinear 900 MHz antenna from coax.